Capturing The Stage: Microphone Approaches For The Performing Arts

night-vintage-music-bokeh

The live sound world goes well beyond the concert realm into areas such as the performing arts, including theatrical plays, musicals, and opera. It also can extend to things like magic shows, dance troupes, puppet shows, jugglers, and even ventriloquists.

Each act presents special microphone requirements, which we’ll explore here. Performing arts applications usually involve at least one of four types: floor mics, hanging mics, wireless lavalier mics, and wireless headworn mics.

On The Floor

Stage floor microphones, also known as boundary mics and commonly seen on boardroom tables as well, are quite effective for area pickup of stage productions, particularly if you’re on a tight budget. These mics offer a half-supercardioid or half-cardioid polar pattern, which rejects sound from the rear such as a pit orchestra.

They should be placed on the stage floor near the footlights. They’re nearly invisible so they don’t detract from the set. Some models are rugged enough to withstand kicks by dancers and can even be stepped on without damage.

Why not use a conventional mic on a desk stand? Sound reflections from the stage floor can color the tone quality and give a hollow sound. That’s due to phase interference between the direct sound from the actors, and delayed reflected sound off the stage floor. Boundary (floor) mics capture the direct and reflected sounds in phase, preventing the hollow, comb-filter effect.

With the proper loudspeaker placement, floor mics can sound clear and natural, and can be turned up loud enough for everyone to hear the performance and understand the words. One centrally located floor mic might work effectively with a 20-foot-wide stage, but typically, the best results are attained with mics spaced 12 to 15 feet apart.

They’re designed to not be sensitive to floor vibrations, but they do “hear” footsteps acoustically, as our ears do. Normally this isn’t a problem because the audience sees and hears the actors walking across the stage.

Many auditoriums are designed with loudspeakers over or near the stage, which can cause feedback with floor mics (and hanging mics). If you’re able to move the loudspeakers, great, but if not, sometimes the only solution is to go with a closer miking solution such as lavalier or headworn.

Here are some tips to enhance gain-before-feedback with stage floor mics:

  1. Place/move loudspeakers close to the audience and as far from the mics as possible. Ideally, if you’re working with a portable PA, place the loudspeakers near the side walls, even with the third row from the front. If coverage isn’t reaching far enough, add two more loudspeakers, left and right, further into the audience area.
  2. Ride the mic faders on the mixer up and down, following the action on stage. Ideally only one mic is on at a time. The more open mics, the more feedback.
  3. Place the mics as close to the actors as possible (without getting in their way).
  4. Train the actors to project their voices loudly toward the audience.
  5. Don’t cover the mic grille holes with tape. It can cause feedback and change the sound of the mic.
  6. If you can’t hear sibilance (“s” sounds) clearly, gently boost high-frequency EQ (just a little) at 10 kHz, but watch out for feedback.
  7. Do not use compression. It softens loud sounds, and you might need that extra volume.
  8. If the stage is carpeted, put each mic on a hard, thin foot-square panel of 1/8-inch-thick masonite or something similar, preventing high-frequency absorption by the carpet.
  9. Optional: Use a feedback suppressor or 1/3-octave graphic EQ between the mixing console and the power amplifier. Turn down frequencies that feed back just enough to stop the ringing.
  10. Optional: Delay the signal going to the loudspeakers so that the audience will localize the sound on stage.

Getting The Hang

If it’s hard to hear actors farther upstage, hang one to three miniature mics. By far, the best results will be obtained by using mics designed for this purpose, and they’re the same as those used for choirs.

Hanging mics come in two parts – the mic itself, joined by an electronics module at the end of a long cable. Being directional, hanging mics pick up from the front and reject sound from rear, which reduces feedback.

They can be flown from the gridwork over the stage, near the upstage actors. As with floor mics, hanging mics should be turned up and down as needed.

Wireless lavalier and headworn mics are usually the preferred way to go in performing arts applications, if the budget allows. Or, lead actors can be outfitted with these closer mics, with the rest of the production captured with floor and/or hanging mics for the ensemble. The advantage is obvious – capturing the source more directly and cleanly will lead to a better result.

Wireless lavalier mics can clip on clothing, or be hung over the actor’s forehead with the cable running through the hair (some mic models are even sweat-resistant), and then plugging into a beltpack transmitter. Often even better, use one of the many options of quality headworn mics that have come on the market within the past decade.

These place the mic element very close to the mouth, resulting in optimum gain before feedback and clarity. Note that best wireless practices should be followed, with the distance between transmitters and receivers as short as possible, and the path uncluttered. And be sure to check those transmitter batteries before each performance.

Adjust the audio trim pot of transmitters to be as high as possible without distortion:

  1. Turn up the audio trim pot all the way (full clockwise)
  2. Have actors wear their mics and talk loudly while transmitting.
  3. Listen to the reproduced sound. If it’s distorted, ease down the trim pot a little at a time until the distortion stops. Use a plastic screwdriver to avoid de-tuning the transmitter.

Whatever approach you take is great, as long as it helps realize the goal of clear, natural sound marked by high intelligibility and loud enough to understand.

Read more at: prosoundweb.com

Facebook
Twitter
Linkedin0
Google+0
GMail0
SMS0
Whatsapp0